[linux] RedHat a SMP

Michal Kapalka kapalka na mfn.sk
Čtvrtek Prosinec 12 13:45:44 CET 2002


Uz si to nepametam ale mam pocit ze to malo nieco do cinenia s ACPI ale
neviem na isto ten server som skladal před 1,5 rokom 

Michal Kapaka 

Toto je vipis dmesg :

CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 731.26 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 3000000
Getting ID: c000000
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 9
Booting processor 1/0 eip 3000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#1
CPU#1 (phys ID: 0) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1605.63 BogoMIPS
Stack at about c1895fb8
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
OK.
CPU1: Intel Pentium III (Coppermine) stepping 06
CPU has booted.
Before bogomips.
Total of 2 processors activated (3207.98 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-13, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21,
2-22, 2-23 not connected.
..TIMER: vector=49 pin1=2 pin2=0
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00178011
.......     : max redirection entries: 0017
.......     : IO APIC version: 0011
 WARNING: unexpected IO-APIC, please mail
          to linux-smp na vger.kernel.org
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00  1    0    0   0   0    0    0    00
 01 003 03  0    0    0   0   0    1    1    39
 02 003 03  0    0    0   0   0    1    1    31
 03 003 03  0    0    0   0   0    1    1    41
 04 003 03  0    0    0   0   0    1    1    49
 05 003 03  1    1    0   1   0    1    1    51
 06 003 03  0    0    0   0   0    1    1    59
 07 003 03  0    0    0   0   0    1    1    61
 08 003 03  0    0    0   0   0    1    1    69
 09 003 03  0    0    0   0   0    1    1    71
 0a 003 03  1    1    0   1   0    1    1    79
 0b 003 03  1    1    0   1   0    1    1    81
 0c 003 03  0    0    0   0   0    1    1    89
 0d 000 00  1    0    0   0   0    0    0    00
 0e 003 03  0    0    0   0   0    1    1    91
 0f 003 03  0    0    0   0   0    1    1    99
 10 000 00  1    0    0   0   0    0    0    00
 11 000 00  1    0    0   0   0    0    0    00
 12 000 00  1    0    0   0   0    0    0    00
 13 000 00  1    0    0   0   0    0    0    00
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 803.6045 MHz.
..... host bus clock speed is 133.9339 MHz.
cpu: 0, clocks: 1339339, slice: 446446
CPU0<T0:1339328,T1:892880,D:2,S:446446,C:1339339>
cpu: 1, clocks: 1339339, slice: 446446
CPU1<T0:1339328,T1:446432,D:4,S:446446,C:1339339>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xf0d00, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting
PCI: Disabled enhanced CPU to PCI posting #2
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
apm: disabled - APM is not SMP safe.
Starting kswapd v1.8
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
block: queued sectors max/low 340109kB/209037kB, 1024 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
HPT370: IDE controller on PCI bus 00 dev 60
HPT370: chipset revision 3
HPT370: not 100% native mode: will probe irqs later
    ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:DMA, hdh:pio
hda: IRQ probe failed (0xfffffff8)
hda: IRQ probe failed (0xfffffff8)
hda: no response (status = 0x0a), resetting drive
hda: IRQ probe failed (0xfffffff8)
hda: no response (status = 0x0a)
hdb: IRQ probe failed (0xfffffff8)
hdb: IRQ probe failed (0xfffffff8)
hdb: no response (status = 0x0a), resetting drive
hdb: IRQ probe failed (0xfffffff8)
hdb: no response (status = 0x0a)
hde: WDC WD400BB-00AUA1, ATA DISK drive
hdg: WDC WD400BB-32AUA1, ATA DISK drive
ide2 at 0xa800-0xa807,0xa402 on irq 11
ide3 at 0xa000-0xa007,0x9802 on irq 11
hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
UDMA(100)
hdg: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
UDMA(100)
Partition check:
 hde: hde1 hde2 < hde5 hde6 hde7 >
 hdg: hdg1 hdg2 < hdg5 hdg6 hdg7 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 341k freed
Serial driver version 5.02 (2000-08-09) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 8, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010 detected with Symbios NVRAM
sym53c8xx: at PCI bus 0, device 8, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010 detected with Symbios NVRAM
sym53c1010-0: rev 0x1 on pci bus 0 device 8 function 0 irq 5
sym53c1010-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
00/4e/a0/01/00/04
sym53c1010-0: final   SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
00/4e/80/00/08/04
sym53c1010-0: on-chip RAM at 0xfb800000
sym53c1010-0: resetting, command processing suspended for 2 seconds
sym53c1010-0: restart (scsi reset).
sym53c1010-0: enabling clock multiplier
sym53c1010-0: handling phase mismatch from SCRIPTS.
sym53c1010-0: Downloading SCSI SCRIPTS.
sym53c1010-1: rev 0x1 on pci bus 0 device 8 function 1 irq 11
sym53c1010-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
00/4e/a0/01/00/04
sym53c1010-1: final   SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
00/4e/80/00/08/04
sym53c1010-1: on-chip RAM at 0xfa800000
sym53c1010-1: resetting, command processing suspended for 2 seconds
sym53c1010-1: restart (scsi reset).
sym53c1010-1: enabling clock multiplier
sym53c1010-1: handling phase mismatch from SCRIPTS.
sym53c1010-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
scsi1 : sym53c8xx - version 1.6b
sym53c1010-0: command processing resumed
sym53c1010-1: command processing resumed
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 252k freed
Adding Swap: 1024088k swap-space (priority -1)
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Via 686A parallel port: io=0x378, irq=7
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw na saw.sw.com.sg> and others
eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:1E:85:4B, I/O
at 0xb800, IRQ 10.
  Board assembly 733470-006, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
TCP: Treason uncloaked! Peer 192.168.1.208:4561/80 shrinks window
2342517005:2342518029. Repaired.





Další informace o konferenci linux