[linux] USB Card Reader

[Michal Tarana]

Hello,
^^^^^^

> Tvoje problemy mozno suvisia s tymi, co mam ja. Este stale to nie je
> u mna uspokojivo vyriesenie. Skus sa pozriet na diskusiu, ktora sa
> odohrala v tomto mailingliste od 2005-01-10 do 2005-02-03. Hladaj spravy
> s predmetom "USB kluc a prechod na jadro 2.6.10".
Noo...diskusiu som si precital, ale nie som z toho mudry. Nemam problem
napriklad s USB-klucom. Mal som, tusim, problem s fotakom, ale to bolo
nejake zdivene vtedy mozno aj niecim inym. Ale s inymi zariadeniami ako
citackami, problemy nemam. Tak neviem. Mam pocit, ze v poslednom case sa
to sprava inak v kazdej novej verzii jadra:-(. Tak neviem...naozaj
neviem.

Dakujem a prajem prijemny den.
	Michal


> > Mam USB citacku pamatovych kariet kombinovanu 4v1. Ked to pichnem do
> > Debianu (kernel-2.6.10), dostanem do dmesg:
> > 
> > hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
> > hub 2-0:1.0: state 5 ports 3 chg fff8 evt 0002
> > ohci_hcd 0000:00:01.3: GetStatus roothub.portstatus [0] = 0x00010101 CSC
> > PPS CCShub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
> > hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> > ohci_hcd 0000:00:01.3: GetStatus roothub.portstatus [0] = 0x00100103
> > PRSC PPS PES CCS
> > usb 2-1: new full speed USB device using ohci_hcd and address 3
> > ohci_hcd 0000:00:01.3: GetStatus roothub.portstatus [0] = 0x00100103
> > PRSC PPS PES CCS
> > usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
> > usb 2-1: default language 0x0409
> > usb 2-1: Product: USB 8-in-1 Card Reader
> > usb 2-1: Manufacturer: OTi
> > usb 2-1: SerialNumber: 0123456789abcdef
> > usb 2-1: hotplug
> > usb 2-1: adding 2-1:1.0 (config #1, interface 0)
> > usb 2-1:1.0: hotplug
> > usb-storage 2-1:1.0: usb_probe_interface
> > usb-storage 2-1:1.0: usb_probe_interface - got id
> > scsi1 : SCSI emulation for USB Mass Storage devices
> > usb-storage: device found at 3
> > usb-storage: waiting for device to settle before scanning
> >   Vendor: OTi       Model: CF CARD Reader    Rev: 2.00
> >   Type:   Direct-Access                      ANSI SCSI revision: 00
> > Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
> > usb-storage: device scan complete
> > 
> > Ale vnutri uz mam kartu, ktoru to zariadenie z nejakeho dovodu nevidi.
> > Na jej zasunutie, vysunutie system vobec nereaguje. Pod Windows to islo
> > dobre. Ked skusim akokolvek pristupovat na tu kartu (primontovat, dalebo
> > cokolvek ine), dostanem hlasku: Nenajdene ziadne medium. Neviem,
> > nestretol sa s tym uz niekto nahodou? Ak ano, velmi by ma potesila
> > nejaka rada. Tentoraz to nie nieco typu zle zasunuty kabel:-). Mam
> > podporu pre usb-storage, scsi-disk a scsi-generic device.