[linux] gnokiirc

[Ing. Jan ONDREJ]

Ahoj,

  pridaj si este:

    connection = bluetooth # inak je to tusim serial

  uprav:

    rfcomchannel = 15 # tusim to ma byt 15 (aspon u mna)

Ten rfcomm channel zistis cez sdptool browse 00:02:EE:0E:87:B6
Pravdaze zariadenia musis mat uz sparovane, bluetooth ti musi fungovat
spravne. Viac uspechov ale asi dosiahnes s programom gammu/wammu,
ktory aspon na mojej nokii vie robit ovela viac ukonov ako gnokii
(aj ked nevyzera grafiky az tak pekne).

		SAL

On Fri, Jul 22, 2005 at 01:21:22AM +0200, Pavol Lajciak wrote:
> Ahojte.
> 
> Mam Nokii 6310 a SiW Bluetooth adapter. Nemate niekto podobnu
> konfiguraciu a gnokiirc k dispozicii.
> 
> Pri mojom konfiguraku gnokii vypise. (vid na konci) Dakujem za radu.
> Pritom som sa ho v konfiguraku snazil presvedcit, ze ide o bluetooth.
> 
> Pavol
> 
> [pavol na localhost pavol]$ gnokii --identify
> GNOKII Version 0.6.7
> Gnokii serial_open: open: No such file or directory
> Couldn't open FBUS device: No such file or directory
> Gnokii serial_open: open: No such file or directory
> Couldn't open FBUS device: No such file or directory
> Gnokii serial_open: open: No such file or directory
> Couldn't open FBUS device: No such file or directory
> Telephone interface init failed: Command failed.
> Quitting.
> 

> # This is a sample ~/.gnokiirc file.  Copy it into your
> # home directory and name it .gnokiirc.
> #
> 
> [global]
> 
> # Set port to the physical serial port used to connect to your phone.
> # Linux version is:
> # port = /dev/ttyS0
> #
> # For MacOSX you will need something like:
> # port = /dev/cu.USA28X1P1.1
> #
> # For Win32 you want to use:
> # port = com1:
> # or similiar.
> #
> # Use this setting also for the Bluetooth connection:
> port =  00:02:EE:0E:87:B6
> 
> # Set model to the model number of your phone. For the
> # Symbian phones use:
> # model = series60
> # For other non-Nokia phones and when you want to use AT
> # mode use:
> # model = AT
> # If you can't figure out what to put here read the FAQ.
> # If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
> model = 6310
> 
> # Initlength controls the number of characters sent to the
> # phone during initialisation.  You can either set it to
> # the word "default" or a positive integer.
> #
> # You can try setting this value if you want to connect
> # to the phone quicker.  If you've never noticed the
> # connection to be slow, it is suggested that you
> # leave this alone.  Read the initialisation code in fbus-xxxx
> # to understand what this changes if you're curious.
> initlength = default
> 
> # The type of the connection, for IR set this to infrared or irda.
> # For the nk6110 driver only infrared is valid for the IrDA connection.
> # See Docs/gnokii-ir-howto for more detailes on this.
> # If you have 6210/6250/7110 phone and dau9p cable (the one you can
> # use with 6100 series and cannot use hardware modem from the phone)
> # you may want to use 'dau9p' value to get faster initialization.
> # If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
> # you don't use model = AT) you may want to use 'dlr3p' value here.
> # Note that it is recommended and currently the best way to use this
> # cable with nk6510 driver.
> # connection = serial
> 
> # Set this to 'yes' if you want gnokii to set and check the lock file in
> # /var/lock directory. It avoids potential conflicts with other serial
> # port software (eg. minicom). If you have wrong permissions for the
> # directory, a warning will be generated. If you don't want a lockfile, set
> # it to 'no'.
> # use_locking = yes
> 
> # Baudrate to use on serial port connections.
> # Currently used only by models AT and BIP/CIMD. Defaults to 19200.
> # serial_baudrate = 19200
> 
> # Force waiting after each send character the specified usec time.
> # Value -1 forces the fastest 'block' writing,
> # value 0 writes each character separately without any explicite waiting,
> # other positive values specify the appropriate 1/1000000 sec delaying.
> # Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
> #serial_write_usleep = 10000
> 
> # Force serial port handshaking mode, useful primarily for "AT" model.
> # Gnokii "AT" model uses software handshake by default.
> # Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
> #handshake = software
> 
> # If defined (not commented out by '#') it will quit Gnokii anytime
> # when DCD line will drop.
> #require_dcd = 1
> 
> # If you are using a bluetooth connection, you can specify the rfcomm
> # channel number here. Default value is 1.
> rfcomm_channel = 1
> 
> # There may happen various timeouts during the communication with the phone.
> # This parameter enables the retransmission policy. Ie. if the phone doesn't
> # respond, we send the frame again. This happend mainly with the older
> # phones. You may want to enable it when you see mysterious timeouts.
> # Be very carefull with this option. It is suspected to cause phone breakage
> # with new DCT4 phones (like Nokia 6100). By default it is switched off
> # (sm_retry = 0)
> #sm_retry = 1
> 
> # Run the specified script(s) right after opening and initializing the device
> # and before any communucation (right before closing for disconnect_script).
> # You may find handy to use it to connect your modem to SMS Center
> # when using BIP or CIMD protocols
> # Non-absolute path is relative to the specific directory where gnokii is run!
> #connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
> #disconnect_script =
> 
> # When sending SMS you can experience timeouts. This is the feature of the
> # overloaded SMSCs. The phones waits for the response from the SMSC confirming
> # that it received the short message. When the SMSC is DoSed with many requests
> # it will take more time to get the response. Adjust it to your needs. The
> # value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
> # forever.
> smsc_timeout = 10
> 
> # Set bindir to point to the location of the various gnokiid binaries.
> # In particular ensure that mgnokiidev is in this location, with
> # permissions 4750, owned by root, group gnokii.  Ensure you
> # are in the gnokii group and that the group exists...
> [gnokiid]
> bindir = /usr/local/sbin/
> 
> # Any entries in the following two sections will be set as environment
> # variables when running the scripts.
> # Handy for use for $VAR substitutions in your chat(8) script.
> [connect_script]
> TELEPHONE = PaulusNokia6310
> [disconnect_script]
> 
> 
> # The following parameters control how libgnokii handle the debugging messages.
> # Currently there are three categories: "debug" controls the libgnokii
> # normal debug output, "rlpdebug" controls the debug output of the RLP
> # subsystem, and "xdebug" is used by the xgnokii or smsd.
> 
> [logging]
> 
> # where to log the debug output (on: stderr)
> debug = off
> 
> # where to log the rlp debug output (on: stderr)
> rlpdebug = off
> 
> # where to log X debug output (on: stderr)
> xdebug = off

> _______________________________________________
> http://lists.linux.sk/listinfo/linux
> Prehladavanie archivu: http://search.lists.linux.sk
> Meta FAQ: http://www.sklug.sk/lists/linux/metafaq.html