[linux] Kernel 2.6.8.1 MIPS - uprava firmware
Kocur
kocur na erbe-ba.sk
Pátek Únor 12 19:30:55 CET 2010
pokial by niekoho zaujimal boot log.................
<0>Rebooting in 1
seconds..
CFE version 1.0.37-6.5.17 for BCM96348 (32bit,SP,BE)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
Unknown PHY type
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x805256C0 (1197760)
Initialized Data: 0x8041CCE0 - 0x8041ED40 (8288)
BSS Area: 0x8041ED40 - 0x804236C0 (18816)
Local Heap: 0x804236C0 - 0x805236C0 (1048576)
Stack Area: 0x805236C0 - 0x805256C0 (8192)
Text (code) segment: 0x80401000 - 0x8041CCE0 (113888)
Boot area (physical): 0x00526000 - 0x00566000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Board Id Name : 96348GW-11
Psi size in KB : 48
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:18:f3:dd:bf:a1
Ethernet PHY Type : External Switch Using Reverse MII
Memory size in MB : 16
CMT Thread Number : 0
Dying Gasp Enable (0:Disable 1:Enable) : 1
*** Press Enter to stop auto run (3 seconds) ***
Auto run second count down: 0
0x80010000/2183301 0x80225085/3963 Entry at 0x80213018
Closing network.
Starting program at 0x80213018
Linux version (@) ()
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
Total Flash size: 4096K with 71 sectors
96348GW-11 prom init
CPU revision is: 00029107
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=81:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13540k/16000k available (1604k kernel code, 2440k reserved, 451k
data, 76k init, 0k highmem)
Calibrating delay loop... 255.59
BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096
bytes)
Checking for 'wait' instruction...
unavailable.
NET: Registered protocol family
16
MPI: No Card is in the PCMCIA
slot
Can't analyze prologue code at
8019f934
SCSI subsystem
initialized
usbcore: registered new driver
usbfs
usbcore: registered new driver
hub
loop: loaded (max 8
devices)
PPP generic driver version
2.4.2
NET: Registered protocol family
24
Using noop io
scheduler
bcm963xx_mtd driver
v1.0
PCI: Enabling device 0000:00:02.2 (0000 ->
0002)
ehci_hcd 0000:00:02.2: Philips Semiconductors USB 2.0 Host
Controller
PCI: Setting latency timer of device 0000:00:02.2 to
64
ehci_hcd 0000:00:02.2: irq 6, pci mem
b0030000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number
1
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 0.95, driver
2004-May-10
hub 1-0:1.0: USB hub
found
hub 1-0:1.0: 2 ports
detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
ohci_hcd: block sizes: ed 64 td
64
PCI: Enabling device 0000:00:02.0 (0000 ->
0002)
ohci_hcd 0000:00:02.0: Philips Semiconductors USB 1.1 Host
Controller
PCI: Setting latency timer of device 0000:00:02.0 to
64
ohci_hcd 0000:00:02.0: irq 6, pci mem
b0010000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number
2
hub 2-0:1.0: USB hub
found
hub 2-0:1.0: 1 port
detected
usb 1-1: new high speed USB device using address
2
PCI: Enabling device 0000:00:02.1 (0000 ->
0002)
ohci_hcd 0000:00:02.1: Philips Semiconductors USB 1.1 Host Controller
(#2)
PCI: Setting latency timer of device 0000:00:02.1 to
64
ohci_hcd 0000:00:02.1: irq 6, pci mem
b0020000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number
3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB DRIVE Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1 sda2 sda3
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb na candelatech.com>
All bugs added by David S. Miller <davem na redhat.com>
VFS: Cannot open root device "81:0" or unknown-block(81,0)
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on unknown-block(81,0)
<0>Rebooting in 1 seconds..
Kocur wrote:
> No router je "zaklad" BROADCOM BCM96348
> a ten pouziva svoj vlastny "loader" pre kernel CFE - Common Firmware
> Enviroment
>
> a root particiu nastavujesh pre kernel priamo v konfiguracii kernelu
> podla dokumentacie by to malo byt root=81:0
>
> ale nefunguje mi to...
>
>
> warezman wrote:
>> Co pouzivas ako bootloader? Grub?
>>
>> Parameter na konci by mal byt root=/dev/sda1
>>
>> 2010/2/12 Kocur <kocur na erbe-ba.sk>:
>>
>>> Zdravim ludia...
>>>
>>> neviete ma nakopnut, ako dalej.....
>>>
>>> Upravujem si firmware pre router, a potrebujem dosiahnut aby zariadenie
>>> nabootovalo z usb...
>>> Uz som si dokazal bez problemov zamenit potrebne moduly pre ADSL, spojazdnit
>>> SWAP (kedze 16Mb RAM nic moc)
>>> a plno dalsich uprav. Dospel som ale k bodu, kedy je povodna 4MB FLASHka
>>> mala, a je zapotreby prejst na nejake vacsie zariadenie.
>>>
>>> Zariadenie ma USB porty, do kernelu som si modul usb_storage zakompiloval,
>>> pri boote v logu vidim zariadenie /dev/sdaX
>>> ale neviem nijako donutit kernel, aby mi ako root particiu namontoval
>>> /dev/sda1
>>>
>>> TU SOM SA PROSTE ZASEKOL..............
>>>
>>> v menuconfigu pre kernel je polozka "root device" s parametrom root=31.1 ro
>>> noinitrd..
>>> co by mala byt "particia" v zabudovanej 4MB FLASHke (fs=squashfs)
>>> ale neviem "co tam dat" ked chcem ako root particiu pouzit usb
>>> kluc...............
>>>
>>> dik za radu....
>>> _______________________________________________
>>> https://lists.linux.sk/mailman/listinfo/linux
>>> Meta FAQ: http://www.sklug.sk/lists/linux/metafaq.html
>>>
>>>
>> _______________________________________________
>> https://lists.linux.sk/mailman/listinfo/linux
>> Meta FAQ: http://www.sklug.sk/lists/linux/metafaq.html
>>
>>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> https://lists.linux.sk/mailman/listinfo/linux
> Meta FAQ: http://www.sklug.sk/lists/linux/metafaq.html
------------- další část ---------------
HTML příloha byla odstraněna...
URL: <http://lists.linux.sk/pipermail/linux/attachments/20100212/d799b5e0/attachment.html>
Další informace o konferenci linux