[linux] RedHat a SMP

Čtvrtek Prosinec 12 14:20:11 CET 2002

Hmm, vsimol som si, ze sietovu mas zakompilovanu do jadra... Vidiiis ?? to 
ma nenapadlo.
Ale aj tak som uz postupil, teraz ked spustam jadro so SMP podporou uz mi 
zamrzne, ale predtym mi stihne ukazat, ze CPU1 - not responding, not found
;-))  .

J.

On Thu, 12 Dec 2002, Michal Kapalka wrote:

> 
> Uz si to nepametam ale mam pocit ze to malo nieco do cinenia s ACPI ale
> neviem na isto ten server som skladal pøed 1,5 rokom 
> 
> Michal Kapaka 
> 
> Toto je vipis dmesg :
> 
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 256K
> Intel machine check reporting enabled on CPU#0.
> CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
> CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
> CPU: Common caps: 0383fbff 00000000 00000000 00000000
> CPU0: Intel Pentium III (Coppermine) stepping 06
> per-CPU timeslice cutoff: 731.26 usecs.
> Getting VERSION: 40011
> Getting VERSION: 40011
> Getting ID: 3000000
> Getting ID: c000000
> Getting LVT0: 8700
> Getting LVT1: 400
> enabled ExtINT on CPU#0
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> CPU present map: 9
> Booting processor 1/0 eip 3000
> Setting warm reset code and vector.
> 1.
> 2.
> 3.
> Asserting INIT.
> Waiting for send to finish...
> +Deasserting INIT.
> Waiting for send to finish...
> +#startup loops: 2.
> Sending STARTUP #1.
> After apic_write.
> Initializing CPU#1
> CPU#1 (phys ID: 0) waiting for CALLOUT
> Startup point 1.
> Waiting for send to finish...
> +Sending STARTUP #2.
> After apic_write.
> Startup point 1.
> Waiting for send to finish...
> +After Startup.
> Before Callout 1.
> After Callout 1.
> CALLIN, before setup_local_APIC().
> masked ExtINT on CPU#1
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Calibrating delay loop... 1605.63 BogoMIPS
> Stack at about c1895fb8
> CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 256K
> Intel machine check reporting enabled on CPU#1.
> CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
> CPU serial number disabled.
> CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
> CPU: Common caps: 0383fbff 00000000 00000000 00000000
> OK.
> CPU1: Intel Pentium III (Coppermine) stepping 06
> CPU has booted.
> Before bogomips.
> Total of 2 processors activated (3207.98 BogoMIPS).
> Before bogocount - setting activated=1.
> Boot done.
> ENABLING IO-APIC IRQs
> ...changing IO-APIC physical APIC ID to 2 ... ok.
> Synchronizing Arb IDs.
> init IO_APIC IRQs
>  IO-APIC (apicid-pin) 2-0, 2-13, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21,
> 2-22, 2-23 not connected.
> ..TIMER: vector=49 pin1=2 pin2=0
> number of MP IRQ sources: 15.
> number of IO-APIC #2 registers: 24.
> testing the IO APIC.......................
> 
> IO APIC #2......
> .... register #00: 02000000
> .......    : physical APIC id: 02
> .... register #01: 00178011
> .......     : max redirection entries: 0017
> .......     : IO APIC version: 0011
>  WARNING: unexpected IO-APIC, please mail
>           to linux-smp na vger.kernel.org
> .... register #02: 00000000
> .......     : arbitration: 00
> .... IRQ redirection table:
>  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
>  00 000 00  1    0    0   0   0    0    0    00
>  01 003 03  0    0    0   0   0    1    1    39
>  02 003 03  0    0    0   0   0    1    1    31
>  03 003 03  0    0    0   0   0    1    1    41
>  04 003 03  0    0    0   0   0    1    1    49
>  05 003 03  1    1    0   1   0    1    1    51
>  06 003 03  0    0    0   0   0    1    1    59
>  07 003 03  0    0    0   0   0    1    1    61
>  08 003 03  0    0    0   0   0    1    1    69
>  09 003 03  0    0    0   0   0    1    1    71
>  0a 003 03  1    1    0   1   0    1    1    79
>  0b 003 03  1    1    0   1   0    1    1    81
>  0c 003 03  0    0    0   0   0    1    1    89
>  0d 000 00  1    0    0   0   0    0    0    00
>  0e 003 03  0    0    0   0   0    1    1    91
>  0f 003 03  0    0    0   0   0    1    1    99
>  10 000 00  1    0    0   0   0    0    0    00
>  11 000 00  1    0    0   0   0    0    0    00
>  12 000 00  1    0    0   0   0    0    0    00
>  13 000 00  1    0    0   0   0    0    0    00
>  14 000 00  1    0    0   0   0    0    0    00
>  15 000 00  1    0    0   0   0    0    0    00
>  16 000 00  1    0    0   0   0    0    0    00
>  17 000 00  1    0    0   0   0    0    0    00
> IRQ to pin mappings:
> IRQ0 -> 0:2
> IRQ1 -> 0:1
> IRQ3 -> 0:3
> IRQ4 -> 0:4
> IRQ5 -> 0:5
> IRQ6 -> 0:6
> IRQ7 -> 0:7
> IRQ8 -> 0:8
> IRQ9 -> 0:9
> IRQ10 -> 0:10
> IRQ11 -> 0:11
> IRQ12 -> 0:12
> IRQ14 -> 0:14
> IRQ15 -> 0:15
> .................................... done.
> calibrating APIC timer ...
> ..... CPU clock speed is 803.6045 MHz.
> ..... host bus clock speed is 133.9339 MHz.
> cpu: 0, clocks: 1339339, slice: 446446
> CPU0<T0:1339328,T1:892880,D:2,S:446446,C:1339339>
> cpu: 1, clocks: 1339339, slice: 446446
> CPU1<T0:1339328,T1:446432,D:4,S:446446,C:1339339>
> checking TSC synchronization across CPUs: passed.
> Setting commenced=1, go go go
> PCI: PCI BIOS revision 2.10 entry at 0xf0d00, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Disabled enhanced CPU to PCI posting
> PCI: Disabled enhanced CPU to PCI posting #2
> Unknown bridge resource 0: assuming transparent
> Unknown bridge resource 1: assuming transparent
> Unknown bridge resource 2: assuming transparent
> PCI: Using IRQ router VIA [1106/0686] at 00:04.0
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
> apm: disabled - APM is not SMP safe.
> Starting kswapd v1.8
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> block: queued sectors max/low 340109kB/209037kB, 1024 slots per queue
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 21
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
>     ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> HPT370: IDE controller on PCI bus 00 dev 60
> HPT370: chipset revision 3
> HPT370: not 100% native mode: will probe irqs later
>     ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:DMA, hdf:pio
>     ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:DMA, hdh:pio
> hda: IRQ probe failed (0xfffffff8)
> hda: IRQ probe failed (0xfffffff8)
> hda: no response (status = 0x0a), resetting drive
> hda: IRQ probe failed (0xfffffff8)
> hda: no response (status = 0x0a)
> hdb: IRQ probe failed (0xfffffff8)
> hdb: IRQ probe failed (0xfffffff8)
> hdb: no response (status = 0x0a), resetting drive
> hdb: IRQ probe failed (0xfffffff8)
> hdb: no response (status = 0x0a)
> hde: WDC WD400BB-00AUA1, ATA DISK drive
> hdg: WDC WD400BB-32AUA1, ATA DISK drive
> ide2 at 0xa800-0xa807,0xa402 on irq 11
> ide3 at 0xa000-0xa007,0x9802 on irq 11
> hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
> UDMA(100)
> hdg: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
> UDMA(100)
> Partition check:
>  hde: hde1 hde2 < hde5 hde6 hde7 >
>  hdg: hdg1 hdg2 < hdg5 hdg6 hdg7 >
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK: Compressed image found at block 0
> Freeing initrd memory: 341k freed
> Serial driver version 5.02 (2000-08-09) with MANY_PORTS MULTIPORT
> SHARE_IRQ SERIAL_PCI ISAPNP enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> Real Time Clock Driver v1.10d
> md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md.c: sizeof(mdp_super_t) = 4096
> autodetecting RAID arrays
> autorun ...
> ... autorun DONE.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 32768)
> Linux IP multicast router 0.06 plus PIM-SM
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> EXT2-fs warning: checktime reached, running e2fsck is recommended
> VFS: Mounted root (ext2 filesystem).
> SCSI subsystem driver Revision: 1.00
> sym53c8xx: at PCI bus 0, device 8, function 0
> sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
> sym53c8xx: 53c1010 detected with Symbios NVRAM
> sym53c8xx: at PCI bus 0, device 8, function 1
> sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
> sym53c8xx: 53c1010 detected with Symbios NVRAM
> sym53c1010-0: rev 0x1 on pci bus 0 device 8 function 0 irq 5
> sym53c1010-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
> sym53c1010-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
> 00/4e/a0/01/00/04
> sym53c1010-0: final   SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
> 00/4e/80/00/08/04
> sym53c1010-0: on-chip RAM at 0xfb800000
> sym53c1010-0: resetting, command processing suspended for 2 seconds
> sym53c1010-0: restart (scsi reset).
> sym53c1010-0: enabling clock multiplier
> sym53c1010-0: handling phase mismatch from SCRIPTS.
> sym53c1010-0: Downloading SCSI SCRIPTS.
> sym53c1010-1: rev 0x1 on pci bus 0 device 8 function 1 irq 11
> sym53c1010-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
> sym53c1010-1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
> 00/4e/a0/01/00/04
> sym53c1010-1: final   SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
> 00/4e/80/00/08/04
> sym53c1010-1: on-chip RAM at 0xfa800000
> sym53c1010-1: resetting, command processing suspended for 2 seconds
> sym53c1010-1: restart (scsi reset).
> sym53c1010-1: enabling clock multiplier
> sym53c1010-1: handling phase mismatch from SCRIPTS.
> sym53c1010-1: Downloading SCSI SCRIPTS.
> scsi0 : sym53c8xx - version 1.6b
> scsi1 : sym53c8xx - version 1.6b
> sym53c1010-0: command processing resumed
> sym53c1010-1: command processing resumed
> VFS: Mounted root (ext2 filesystem) readonly.
> change_root: old root has d_count=3
> Trying to unmount old root ... okay
> Freeing unused kernel memory: 252k freed
> Adding Swap: 1024088k swap-space (priority -1)
> Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
> SMSC Super-IO detection, now testing Ports 2F0, 370 ...
> parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
> parport0: cpp_daisy: aa5500ff(38)
> parport0: assign_addrs: aa5500ff(38)
> parport0: cpp_daisy: aa5500ff(38)
> parport0: assign_addrs: aa5500ff(38)
> parport_pc: Via 686A parallel port: io=0x378, irq=7
> eepro100.c:v1.09j-t 9/29/99 Donald Becker
> http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
> eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
> <saw na saw.sw.com.sg> and others
> eth0: Intel Corporation 82557 [Ethernet Pro 100], 00:E0:18:1E:85:4B, I/O
> at 0xb800, IRQ 10.
>   Board assembly 733470-006, Physical connectors present: RJ45
>   Primary interface chip i82555 PHY #1.
>   General self-test: passed.
>   Serial sub-system self-test: passed.
>   Internal registers self-test: passed.
>   ROM checksum self-test: passed (0x04f4518b).
> TCP: Treason uncloaked! Peer 192.168.1.208:4561/80 shrinks window
> 2342517005:2342518029. Repaired.
> 
> 
> _______________________________________________
> http://lists.linux.sk/listinfo/linux
> Prehµadávanie archívu: http://search.lists.linux.sk
> Meta FAQ: http://faq.lists.linux.sk
> 

-- 
!! POZOR !!
Skor, ako mi poslete prilohu s MS OFFICE (doc,xls,ppt,acs a dalsie), 
precitajte si prosim stranku:
	http://fyzika.utc.sk/~remenec/priloha.html
Dakujem.

=======================================================
REMENEC Juraj			miestnost: NB322
Elektrotechnicka fakulta	tel/klapka:041-513/2366
Katedra Fyziky			mobil:0903 885 170
Velky Diel 026			ICQ: 174246364
Zilina				remenec na fyzika.utc.sk
=======================================================
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

	Nikto nebude nikdy potrebovat viac, nez 640 kB RAM,
				Bill Gates, 1981

	Windows 95 potrebuje minimalne 8 MB RAM,
				Bill Gates, 1996

	Nikto nebude nikdy potrebovat WINDOWS 95,
				logicky zaver

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --