[linux] Fw: p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame dropped.
Miro Betak
betak na orga.sk
Čtvrtek Květen 23 10:13:56 CEST 2002
Ahojte
Pokusam sa rochodit wireless kartu NWH 630 pod RedHat linuxom 7.2,
jadro 2.4.7-10, ovladace linux-wlan-ng-0.1.8-pre13-ndc-v4
Ovladace sa natiahnu v pohode -
vypis z lsmod :
Module Size Used by
8139too 12640 1
prism2_plx 46592 1 (autoclean)
p80211 9936 1 (autoclean) [prism2_plx]
ext3 61936 1
jbd 38976 1 [ext3]
vypis z messages:
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal journal
p80211.o: 0.1.8-pre12 Loaded
init_module: prism2_pci.o: 0.1.8-pre12 Loaded
init_module: dev_info is: prism2_pci
Found National Datacomm Corp PCI card(ASIC) at PCI address 0x6600, mapped IRQ 10.
...
A Prism2 PCI device found, mem:0x6600, irq:10, io addr:0x6600
ident: nic h/w: id=0x8003 1.0.0
ident: pri f/w: id=0x15 0.3.0
ident: sta f/w: id=0x1f 0.7.6
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x01:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/2
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/4
PRI-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x01:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1
Prism2 card SN: 000000003841
8139too Fast Ethernet driver 0.9.18a
....
ifconfig wlan0:
wlan0 Link encap:Ethernet HWaddr 00:80:C6:E3:24:9A
inet addr:192.168.0.200 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:86 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:5903 (5.7 Kb) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x6600
Ked sa vsak pokusim pingnut access point, dostanem chybovu hlasku:
p80211knetdev_hard_start_xmit: Tx attempt prior to association, frame dropped.
Zaujimavy je vystup z wlancfg show wlan0:
dot11StationID=00:80:c6:e3:24:9a
dot11PowerManagementMode=active
dot11DesiredSSID=
dot11DesiredBSSType="argument_item_data_is_invalid"
dot11OperationalRateSet=02:04
dot11AuthenticationAlgorithmsEnable1=true
dot11AuthenticationAlgorithmsEnable2=false
dot11PrivacyInvoked=false
dot11WEPDefaultKeyID=0
dot11ExcludeUnencrypted=false
dot11RTSThreshold=2432
dot11FragmentationThreshold=2346
dot11Address1=00:00:00:00:00:00
dot11Address2=00:00:00:00:00:00
dot11Address3=00:00:00:00:00:00
dot11Address4=00:00:00:00:00:00
dot11Address5=00:00:00:00:00:00
dot11Address6=00:00:00:00:00:00
dot11Address7=00:00:00:00:00:00
dot11Address8=00:00:00:00:00:00
dot11Address9=00:00:00:00:00:00
dot11Address10=00:00:00:00:00:00
dot11Address11=00:00:00:00:00:00
dot11Address12=00:00:00:00:00:00
dot11Address13=00:00:00:00:00:00
dot11Address14=00:00:00:00:00:00
dot11Address15=00:00:00:00:00:00
dot11Address16=00:00:00:00:00:00
dot11Address17=00:00:00:00:00:00
dot11Address18=00:00:00:00:00:00
dot11Address19=00:00:00:00:00:00
dot11Address20=00:00:00:00:00:00
dot11Address21=00:00:00:00:00:00
dot11Address22=00:00:00:00:00:00
dot11Address23=00:00:00:00:00:00
dot11Address24=00:00:00:00:00:00
dot11Address25=00:00:00:00:00:00
dot11Address26=00:00:00:00:00:00
dot11Address27=00:00:00:00:00:00
dot11Address28=00:00:00:00:00:00
dot11Address29=00:00:00:00:00:00
dot11Address30=00:00:00:00:00:00
dot11Address31=00:00:00:00:00:00
dot11Address32=00:00:00:00:00:00
p2MMTx=false
p2Comment=
p2LogEvents=false
p2CnfPortType=1
p2CnfOwnMACAddress=00:80:c6:e3:24:9a
p2CnfDesiredSSID=
p2CnfOwnChannel=6
p2CnfOwnSSID=
p2CnfOwnATIMWindow=0
p2CnfSystemScale=1
p2CnfMaxDataLength=2312
p2CnfWDSAddress=00:00:00:00:00:00
p2CnfPMEnabled=false
p2CnfPMEPS=true
p2CnfMulticastReceive=true
p2CnfMaxSleepDuration=100
p2CnfPMHoldoverDuration=100
p2CnfOwnName=
p2CnfWEPDefaultKeyID=0
p2CnfWEPFlags=
p2CnfAuthentication=0
p2CnfTxControl=512
p2CnfRoamingMode=1
p2CnfRcvCrcError=
p2CnfMMLife=65000
p2CnfAltRetryCount=7
p2CnfSTAPCFInfo=1
p2CnfShortPreamble=false
p2CnfBasicRates=0,1
p2CnfSupportedRates=0,1,2,3
p2CreateIBSS=false
p2FragmentationThreshold=2346
p2RTSThreshold=2432
p2TxRateControl=0,1
p2PromiscuousMode=false
p2TickTime=10
Neviem , preco ma polozka dot11DesiredBSSType="argument_item_data_is_invalid takyto argument
nemal by tam byt prave mod add hoc alebo ifrastructure ?
prikladam konfigurak wlan-ng.opts:
#! /bin/sh
# Wireless LAN adapter configuration
#
# etc/pcmcia/wlan-ng.opts
#
# Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved.
# --------------------------------------------------------------------
#
# linux-wlan
#
# The contents of this file are subject to the Mozilla Public
# License Version 1.1 (the "License"); you may not use this file
# except in compliance with the License. You may obtain a copy of
# the License at http://www.mozilla.org/MPL/
#
# Software distributed under the License is distributed on an "AS
# IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
# implied. See the License for the specific language governing
# rights and limitations under the License.
#
# Alternatively, the contents of this file may be used under the
# terms of the GNU Public License version 2 (the "GPL"), in which
# case the provisions of the GPL are applicable instead of the
# above. If you wish to allow the use of your version of this file
# only under the terms of the GPL and not to allow others to use
# your version of this file under the MPL, indicate your decision
# by deleting the provisions above and replace them with the notice
# and other provisions required by the GPL. If you do not delete
# the provisions above, a recipient may use your version of this
# file under either the MPL or the GPL.
#
# --------------------------------------------------------------------
#
# Inquiries regarding the linux-wlan Open Source project can be
# made directly to:
#
# AbsoluteValue Systems Inc.
# info na linux-wlan.com
# http://www.linux-wlan.com
#
# --------------------------------------------------------------------
#
# Portions of the development of this software were funded by
# Intersil Corporation as part of PRISM(R) chipset product development.
#
# --------------------------------------------------------------------
#
# The address format is "scheme,socket,instance,hwaddr".
#
# --------------------------------------------------------------------
case "$ADDRESS" in
*,*,*,*)
#=======ENABLE========================================
# Do we want to enable the card at all? Set to 'n' if you don't
# want the card initialized for normal operation. Helpful for
# (re)loading flash or for test purposes.
WLAN_ENABLE=y
#=======USER MIB SETTINGS=============================
# You can add the assignments for various MIB items
# of your choosing to this variable, separated by
# whitespace. The wlan-ng script will then set each one.
# Just uncomment the variable and set the assignments
# the way you want them.
#USER_MIBS="\
#p2RoamingMode=2"
#p2MMTx=true \
#p2MMFixedLevel=2"
#=======WEP===========================================
# [Dis/En]able WEP. Settings only matter if PrivacyInvoked is true
dot11PrivacyInvoked=false # true|false
dot11WEPDefaultKeyID=0 # 0|1|2|3
dot11ExcludeUnencrypted=true # true|false, in AP this means WEP
# is required for all STAs
# Use the generator string to generate keys (just a convenience)
PRIV_GENERATOR=/sbin/nwepgen # nwepgen, Neesus compatible
PRIV_KEY128=false # keylength to generate
PRIV_GENSTR=""
# or set them explicitly. Set genstr or keys, not both.
dot11WEPDefaultKey0=11:11:11:11:11 # format: xx:xx:xx:xx:xx
#dot11WEPDefaultKey0=11:11:11:11:11:11:11:11:11:11:22:22:22
dot11WEPDefaultKey1=11:11:11:11:11 # e.g. 01:20:03:40:05
dot11WEPDefaultKey2=11:11:11:11:11
dot11WEPDefaultKey3=11:11:11:11:11
#=======STA START=====================================
# SSID is all we have for now
AuthType="opensystem" # opensystem | sharedkey (requires WEP)
DesiredSSID="Wireless" # "any" or "ANY" means any SSID
dot11OwnChannel=6
dot11FragmentationThreshold=2346
dot11RTSThreshold=2432
dot11PowerManagementMode=active #powersave,active
BASICRATES="2 4" # Rates for mgmt&ctl frames (in 500Kb/s)
SUPPRATES="2 4 11 22" # Supported rates in IBSS (in 500Kb/s)
# for IBSS mode
IBSS_MODE=false # true|false
IBSS_BCNINT=100 # Beacon interval (in Kus)
IBSS_DTIMINT=3 # DTIM interval (in beacons)
#=======DOWNLOAD======================================
# Do we need to download code/data to the card?
WLAN_DOWNLOAD=n
WLAN_DOWNLOADER=/sbin/prism2dl
WLAN_DLIMAGE=/etc/wlan_pci/t10002c5.hex
#=======AP START======================================
# If IS_AP is 'y', then the following settings will be
# used in the creation of a BSS with this station acting
# as the AP. If IS_AP is 'n', these settings are ignored.
IS_AP=n # y|n
IS_BRIDGE=y # Are we a bridging AP?
IS_OLDBRIDGE=y # Which kernel bridge code are we using?
APWIREDDEVICE=eth0 # Must be an ethernet device
APBRIDGEDEVICE=apbr0 # Bridge interface name
AP_IPADDR=192.168.200.150 # Bridge IP address (and only bridge)
APSSID="Wireless" # SSID the AP will use, max 32 chars
APBCNINT=100 # Beacon interval (in Kus)
APDTIMINT=3 # DTIM interval (in beacons)
APCFPOLLABLE=false # AP's CFP support (see table below)
APCFPOLLREQ=false # AP's CFP support (see table below)
APCFPPERIOD=3 # CFP period, if CFP enabled(in beacons)
APCFPMAXDURATION=100 # CFP max length (in Kus)
APPROBEDELAY=100 # Not currently used
APCHANNEL=6 # DS channel for BSS (1-14, depends
# on regulatory domain)
APBASICRATES="2 4" # Rates for mgmt&ctl frames (in 500Kb/s)
APOPRATES="2 4 11 22" # Supported rates in BSS (in 500Kb/s)
# Table of CFPOLL* values:
# CFPOLLABLE CFPOLLREQ AP Behavior
#----------------------------------------------------
# false false No Point Coordinator (CFP) at AP
# false true CFP for delivery only (no polling)
# true false CFP delivery and polling
# true true Reserved, do not use
;;
esac
Dakujem za radu
Miro
------------- další část ---------------
HTML příloha byla odstraněna...
URL: http://lists.linux.sk/pipermail/linux/attachments/20020523/0829d669/attachment.html
Další informace o konferenci linux